spec no: dsao7360 rev no: v.1a date: mar/10/2016 page: 1 of 6 approved: wynec checked: allen liu drawn: m.liu e rp: 1201004058 3.5x2.8mm surface mount led lamp part number: AAA3528SURKCGKCT hyper red green features z both chips can be controlled separately. z suitable for all smd assembly and solder process. z available on tape and reel. z package: 2000pcs / reel. z moisture sensitivity level : level 3. z rohs compliant. descriptions the hyper red source color devices are made with al- gainp on gaas substrat e light emitting diode. the green source color devices are made with algainp on gaas substrate li ght emitting diode. package dimensions notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25(0.01") unless otherwise noted.
spec no: dsao7360 rev no: v.1a date: mar/10/2016 page: 2 of 6 approved: wynec checked: allen liu drawn: m.liu e rp: 1201004058 selection guide notes: 1. 1/2 is the angle from optical centerline where the lumi nous intensity is 1/2 of the optical peak value. 2. luminous intensity/ luminous flux: +/-15%. * luminous intensity value is traceable to cie127-2007 standards. absolute maximum ratings at ta=25c electrical / optical characteristics at ta=25c part no. emitting color (material) lens type iv (mcd) [2] @ 20ma v iewing angle [1] min. typ. 2 1/2 AAA3528SURKCGKCT water clear 200 320 120 *55 *100 green (algainp) 40 80 *40 *80 hyper red (algainp) symbol parameter emitting color typ. max. units test conditions peak peak wavelength hyper red green 645 574 nm i f =20ma d [1] dominant wavelength hyper red green 630 570 nm i f =20ma ? 1/2 spectral line half-width hyper red green 28 20 nm i f =20ma c capacitance hyper red green 35 15 pf v f =0v;f=1mhz v f [2] forward voltage hyper red green 1.95 2.1 2.5 2.5 v i f =20ma i r reverse current hyper red green 10 10 ua v r = 5v parameter hyper red green units power dissipation 75 75 mw dc forward current 30 30 ma peak forward current [1] 185 150 ma reverse voltage 5 v operating temperature -40c to +85c storage temperature -40c to +85c notes: 1. wavelength: +/-1nm. 2. forward voltage: +/-0.1v. 3. wavelength value is traceable to cie127-2007 standards. 4. excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradat ion or premature failure. notes: 1. 1/10 duty cycle, 0.1ms pulse width. 2. relative humidity levels maintained between 40% and 60% in pr oduction area are recommended to avoid the build-up of static electricity ? ref jedec/jesd625-a and jedec/j-std-033.
spec no: dsao7360 rev no: v.1a date: mar/10/2016 page: 3 of 6 approved: wynec checked: allen liu drawn: m.liu e rp: 1201004058 AAA3528SURKCGKCT hyper red
spec no: dsao7360 rev no: v.1a date: mar/10/2016 page: 4 of 6 approved: wynec checked: allen liu drawn: m.liu e rp: 1201004058 green
spec no: dsao7360 rev no: v.1a date: mar/10/2016 page: 5 of 6 approved: wynec checked: allen liu drawn: m.liu e rp: 1201004058 AAA3528SURKCGKCT reflow soldering is recommended and the soldering profile is shown below. other soldering methods are not recommended as they might cause damage to the product. recommended soldering pattern (units : mm; tolerance: 0.1) reel dimension tape dimensions (units : mm)
spec no: dsao7360 rev no: v.1a date: mar/10/2016 page: 6 of 6 approved: wynec checked: allen liu drawn: m.liu e rp: 1201004058 packing & label specifications AAA3528SURKCGKCT terms and conditions for the usage of this document 1. the information included in this docum ent reflects representative usage scenarios and is intended for technical reference on ly. 2. the part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. before production usage customer should refer to the latest datasheet for the updated specifications. 3. when using the products referenced in this document, please make sure the produc t is being operated within the environmental and electrical limits specified in the dat asheet. if customer usage exceeds the spec ified limits, kingbright will not be respon sible for any subsequent issues. 4. the information in this document applies to typical usage in consumer electronics applicati ons. if customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with kingbright representative for further assistance. 5. the contents and information of this document may not be reproduced or re-transmitted without permission by kingbright. 6. all design applications should refer to kingbright application notes available at http://www.kingbrightusa.com/applicationnotes
|
